Street and Sidewalk Decals

Rolling vehicle traffic won't damage the decal. Rolling vehicle traffic is defined as straight forward or backwards motion over the graphic. However, stops or turns on the decal may cause permanent and irreversible damage. Materials stored on top of the applied graphics should not be slid or pushed across its surface, as doing so may cause edges to lift and render the graphics unusable.

You won't need any specialized tools, however a rubber hand roller (also known as J-Roller) may make the process easier and ensure proper application of the decal. If desired, this is offered as an optional add-on that can be added to your order while designing it on our design tool. With the exception of very large graphics, installation is simple and easy enough to be done by just one person without additional help. For large graphics, we do recommend additional hands to ensure your decal is applied correctly the first time.

To properly install your outdoor floor decal the surface must first be prepared before application. The application surface where applied should be above freezing when first applied. For best results, apply when the surface temperature is above 50 F. Surface Preparation: 1. Sweep the surface to ensure it is free of any debris such as loose gravel, caked dirt, oils, grease, sand, etc. This will ensure proper adhesion. 2. Ensure the surface is dry. If the surface is greasy or otherwise unclean, power wash the area then allow it to dry before applying your graphic. A commercial degreaser may be necessary for stubborn substances. 3. A mixture of 50/50 to 70/30 percent isopropyl alcohol (IPA) + water can be used for surfaces where adhesion is difficult. After applying the solution, wipe with a soft cloth. A second pass often helps with adhesion. Once the surface is clean and dry you are ready to install your decal. Applying the Decal: 1. Before starting the application process we recommend you lay your graphic with the back liner still still in place on the surface exactly where you intend to install it to ensure proper fit. 2. Remove the brown paper back liner from your decal. Please note that the decal is not repositionable, so it's important that you lay it precisely where you want it on the desired surface. While these decals are not as unforgiving as some of our window and vehicle decals we recommend not letting the adhesive side stick to itself during installation. Multiple people helping during installation of large graphics will help prevent this. 3. Lay the decal on the desired surface, pressing firmly from left to right, top to bottom, ensuring the material conforms to the surface beneath to maximize adhesion. For best results with uneven surfaces you'll need to move slowly and ensure that the decal is fully adhered as you go. Alternatively, you can also peel away only a small portion of the back liner and firmly press the exposed part to the surface first. Then you can slowly and simultaneously peel away the back liner and apply the exposed portion of your decal to the surface to prevent self-sticking. 4. If needed, a hand roller (optional purchase) can be used to ensure the graphic is firmly adhered. 5. Adhesion is instant and, once firmly pressed, the decal is immediately ready for foot and vehicular traffic ("rolling vehicular traffic", no stopping, turning, pivoting, etc.). However, it will take up to 24 hours for the decal's adhesive to fully dry

Removal of the decal is very simple, and they'll come off clean from any unsealed surfaces. To remove the decal, simply peel back one of the corners of the decal and pull it away at a 45 degree angle, removing the graphic in one piece. A squeegee or other flat object may be used to leverage the decal away from the surface in cases where the edges of the graphic have sheared, making grip difficult. No special tools should be needed for removal of your decal.

To clean your graphic(s), lightly spray the decal with water from a low pressure hose and sweep with a broom; avoid harsh cleaning chemicals as they may damage or negatively affect the decal

If you choose to use a pressure washer ensure that it is set to “Low” and is used no closer than 36”. Using a power washer on too intense a setting or too close to the graphic may cause irreversible damage, especially near the edges.

If you need to store your graphics for a period for time before applying them they should be so long as you store them on the original backer they are shipped with and do so for no longer than 2 years in an environment that is above room temperature

Nothing should be stored on top of the graphic, as it may bend, increasing the chances for rippling once the graphic is applied. For graphics which have already been installed, it’s important not to slide anything over the top of the graphic and to avoid turns or stop and starting of wheeled vehicles, as doing so may cause damage to the graphic and decrease its estimated lifespan.

The material we use for the decals is durable for up to a year. It can with stand cold and hot temps. 

Durable street and sidewalk decals that shine wherever they are placed. Made from a PVC-free aluminum foil base and designed to withstand both foot and rolling vehicle traffic. However, this is not suitable for those chemicals. It will soak through it and cause it to peel.